Wasp-bar-code WPS100 Manual de usuario Pagina 55
- Pagina / 466
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4-15
User Preferences
Timeout Between Decodes
Timeout Between Decodes, Same Symbol
This parameter sets the minimum time between decodes of different symbols. It is
programmable in 0.1-second increments from 0.0 to 9.9 seconds. Setting this above 0.4
seconds is recommended.) The default for this parameter is 0.6 seconds.
Scan the bar code below to select a new timeout. Next, scan two numeric bar codes
beginning in Numeric Bar Codes on page D-1 that correspond to the desired timeout.
Single digit numbers must have a leading zero. For example, to set a timeout of 0.5
seconds, scan the bar code below, then scan the “0” and “5” bar codes. If you make an
error, or wish to change your selection, scan Cancel on page D-5.
Timeout Between Same Symbol
Timeout Between Decodes, Different Symbol
This parameter sets the minimum time between decodes of different symbols. It is
programmable in 0.1-second increments from 0.0 to 9.9 seconds. The default for this
parameter is 0.2 seconds.
Scan the bar code below to select a new timeout. Next, scan two numeric bar codes
beginning in Numeric Bar Codes on page D-1 that correspond to the desired timeout.
Single digit numbers must have a leading zero. For example, to set a timeout of 0.5
seconds, scan the bar code below, then scan the “0” and “5” bar codes. If you make an
error, or wish to change your selection, scan Cancel on page D-5.
Timeout Between Different Symbol
- Product Reference Guide 1
- Wasp Technologies, Inc 4
- 1400 10th Street 4
- Plano, TX 75074 4
- Contents 5
- Chapter 6 7
- Appendix D 11
- Numeric Bar Codes 11
- Glossary 11
- About This Guide 13
- Notational Conventions 15
- Related Publications 15
- Wasp Technical Support 15
- Chapter 1 17
- Getting Started 17
- Unpacking Your Scanner 18
- Setting Up the Scanner 19
- Configuring Your Scanner 20
- Removing the Interface Cable 20
- Chapter 2 21
- Scanning 21
- Scanning in Single-Line Mode 22
- Scanning in Omni Mode 23
- Figure 2-8. “Swipe” scanning 26
- Beeper Definitions 27
- LED Definitions 29
- Specular 30
- Reflection 30
- Decode Zone 31
- Chapter 3 33
- Troubleshooting 34
- Technical Specifications 36
- Scanner Signal Descriptions 39
- Chapter 4 41
- User Preferences 41
- Parameter Default 44
- Beeper Tone 46
- *High Frequency 46
- Beeper Volume 47
- *High Volume 47
- Volume Change Trigger Delay 48
- Laser On Time 49
- Beep After Good Decode 50
- *Beep After Good Decode 50
- Low Power Blink 51
- *Low Power - Blink Mode 51
- Scan Pattern Mode 52
- Single-Line Aim Duration 53
- Aim Duration 4 sec 54
- Aim Duration 5 sec 54
- Timeout Between Decodes 55
- Time Delay to Low Power Mode 56
- 60 Minutes 57
- 90 Minutes 57
- Linear UPC/EAN Decode 58
- Chapter 5 59
- Keyboard Wedge Interface 59
- Power supply 60
- (if needed) 60
- Male DIN Keyboard 60
- Keyboard Wedge Host Types 62
- NCR 7052 63
- *North American 64
- French Canadian Win 95/98 65
- Spanish Windows 65
- Italian Windows 66
- Swedish Windows 66
- UK English Windows 66
- Japanese Windows 67
- Brazilian/Portuguese Windows 67
- Ignore Unknown Characters 68
- *Send Bar Codes With Unknown 68
- Keystroke Delay 69
- Intra-Keystroke Delay 70
- Caps Lock On 72
- *Disable Caps Lock On 72
- Caps Lock Override 73
- *Disable Caps Lock Override 73
- Convert Wedge Data 74
- *No Convert 74
- FN1 Substitution 76
- Send Make Break 77
- Keyboard Maps 78
- Figure 5-4. IBM PC/AT 79
- Figure 5-5. NCR 7052 32-KEY 79
- Figure 5-6. NCR 7052 58-KEY 80
- Connecting a USB Interface 94
- USB Default Parameters 96
- USB Host Parameters 97
- French, Windows 98
- German, Windows 98
- French Canadian, Windows 99
- Swedish, Windows 100
- UK English, Windows 100
- Italian, Windows 100
- USB Interface 101
- Portuguese-Brazilian, Windows 101
- Japanese, Windows (ASCII) 101
- USB Keystroke Delay 102
- *No Delay 102
- USB CAPS Lock Override 103
- USB Ignore Unknown Characters 104
- Emulate Keypad 105
- USB Keyboard FN1 Substitution 106
- Function Key Mapping 107
- Simulated Caps Lock 108
- Convert Case 109
- ASCII Character Set 110
- Chapter 7 121
- Symbologies 121
- Scanning Sequence Examples 122
- Errors While Scanning 122
- Symbology Default Parameters 123
- Enable/Disable UPC-A/UPC-E 128
- *Enable UPC-A 128
- *Enable UPC-E 128
- Enable/Disable UPC-E1 129
- *Disable UPC-E1 129
- *Enable EAN-13/JAN-13 130
- *Enable EAN-8/JAN-8 130
- Enable/Disable Bookland EAN 131
- *Disable Bookland EAN 131
- Decode UPC/EAN Supplementals 132
- Ignore Supplementals 133
- Enable 978 Supplemental Mode 134
- *Transmit UPC-A Check Digit 136
- *Transmit UPC-E1 Check Digit 137
- UPC-A Preamble 138
- *System Character 138
- UPC-A Preamble (Continued) 139
- UPC-E Preamble 139
- UPC-E Preamble (Continued) 140
- UPC-E1 Preamble 140
- UPC-E1 Preamble (Continued) 141
- Convert UPC-E to UPC-A 141
- Convert UPC-E1 to UPC-A 142
- EAN Zero Extend 143
- *Disable EAN Zero Extend 143
- UCC Coupon Extended Code 144
- Code 128 145
- Enable/Disable UCC/EAN-128 146
- *Enable UCC/EAN-128 146
- Enable/Disable ISBT 128 147
- *Enable ISBT 128 147
- Code 128 Decode Performance 148
- Enable/Disable Code 39 150
- *Enable Code 39 150
- *Disable Trioptic Code 39 151
- Convert Code 39 to Code 32 152
- Code 32 Prefix 153
- *Disable Code 32 Prefix 153
- Set Lengths for Code 39 154
- Code 39 - Length Within Range 155
- Code 39 - Any Length 155
- *Disable Code 39 Check Digit 156
- Transmit Code 39 Check Digit 157
- *Disable Code 39 Full ASCII 158
- Buffer Code 39 159
- (Enable) 159
- Buffer Data 160
- Clear Transmission Buffer 160
- Transmit Buffer 161
- Code 39 Decode Performance 163
- Enable/Disable Code 93 165
- *Disable Code 93 165
- Set Lengths for Code 93 166
- Code 93 - Length Within Range 167
- Code 93 - Any Length 167
- *Disable Code 11 168
- Set Lengths for Code 11 169
- Code 11 - Length Within Range 170
- Code 11 - Any Length 170
- *One Check Digit 171
- Transmit Code 11 Check Digits 172
- Interleaved 2 of 5 (ITF) 173
- I 2 of 5 - Any Length 175
- *Disable 176
- Transmit I 2 of 5 Check Digit 177
- Convert I 2 of 5 to EAN-13 178
- Discrete 2 of 5 (DTF) 179
- D 2 of 5 - Any Length 181
- Chinese 2 of 5 182
- Codabar (NW - 7) 183
- Set Lengths for Codabar 184
- Codabar - Length Within Range 185
- Codabar - Any Length 185
- CLSI Editing 186
- *Disable CLSI Editing 186
- NOTIS Editing 187
- *Disable NOTIS Editing 187
- Enable/Disable MSI 188
- *Disable MSI 188
- Set Lengths for MSI 189
- MSI - Length Within Range 190
- MSI - Any Length 190
- MSI Check Digits 191
- *One MSI Check Digit 191
- Transmit MSI Check Digit(s) 192
- MSI Check Digit Algorithm 193
- *MOD 10/MOD 10 193
- RSS (Reduced Space Symbology) 194
- RSS Limited 195
- *Disable RSS Limited 195
- RSS Expanded 196
- Convert RSS to UPC/EAN 197
- XXXXXXXXXXXX 198
- XXXXXXXXXXX 198
- 0 1000000XXXXXXXX 198
- Enable Convert RSS to UPC/EAN 199
- Redundancy Level 200
- *Redundancy Level 1 200
- Redundancy Level 2 201
- Redundancy Level 3 201
- Redundancy Level 4 202
- Security Level 203
- * Security Level 0 203
- Security Level 2 204
- Security Level 3 204
- *Normal Intercharacter Gaps 205
- Chapter 8 207
- Miscellaneous Scanner Options 207
- Transmit Code ID Character 210
- Prefix/Suffix Values 211
- Set Value 3 212
- Set Value 4 212
- Set Value 5 213
- FN1 Substitution Values 214
- Scan Data Options 215
- *Data As Is 216
- <DATA> <SUFFIX> 216
- <PREFIX> <DATA> 216
- Data Format Cancel 217
- Transmit “No Read” Message 218
- *Disable No Read 218
- Chapter 9 219
- Advanced Data Formatting 219
- Using ADF Bar Codes 220
- ADF Bar Code Menu Example 220
- Rule 2: The UPC Scanning Rule 221
- Alternate Rule Sets 222
- Default Rules 224
- Special Commands 225
- Save Rule 226
- Erase (Continued) 227
- Quit Entering Rules 227
- Disable Rule Set 228
- Disable Rule Set (Continued) 229
- Criteria 230
- Code Types (Continued) 231
- Code Lengths 238
- Code Lengths (Continued) 239
- Specific String at Start 248
- Any Message OK 249
- Rule Belongs To Set 250
- Rule Belongs To Set 3 251
- Rule Belongs To Set 4 251
- Send Data 252
- Send Data (Continued) 253
- Setup Field(s) 260
- Move Cursor 261
- Move Cursor (Continued) 262
- Skip Ahead 262
- Skip Ahead (Continued) 263
- Skip Back 266
- Skip Back (Continued) 267
- Send Preset Value 269
- Send Preset Value (Continued) 270
- Modify Data 271
- Modify Data (Continued) 272
- Pad Data with Zeros 284
- Stop Pad Zeros 294
- Beep Once 294
- Beep Twice 294
- Beeps (Continued) 295
- Characters) 295
- Send Control C 296
- Send Control B 296
- Send Control D 296
- Send Control E 297
- Send Control G 297
- Send Control F 297
- Send Control H 298
- Send Control I 298
- Send Control J 298
- Send Control K 299
- Send Control L 299
- Send Control M 299
- Send Control P 300
- Send Control O 300
- Send Control N 300
- Send Control Q 301
- Send Control S 301
- Send Control R 301
- Send Control T 302
- Send Control U 302
- Send Control V 302
- Send Control X 303
- Send Control Y 303
- Send Control W 303
- Send Control [ 304
- Send Control Z 304
- Send Control \ 304
- Send Control ] 305
- Send Control 305
- Send Control 6 305
- Keyboard Characters 306
- Send & 308
- Send < 315
- Send > 316
- Send ALT Characters 337
- Send Alt A 338
- Send Alt C 338
- Send Alt B 338
- Send Alt D 339
- Send Alt E 339
- Send Alt F 339
- Send Alt H 340
- Send Alt I 340
- Send Alt G 340
- Send Alt K 341
- Send Alt J 341
- Send Alt L 341
- Send Alt M 342
- Send Alt O 342
- Send Alt N 342
- Send Alt P 343
- Send Alt Q 343
- Send Alt R 343
- Send Alt S 344
- Send Alt T 344
- Send Alt U 344
- Send Alt X 345
- Send Alt V 345
- Send Alt W 345
- Send Alt Y 346
- Send Alt [ 346
- Send Alt Z 346
- Send Alt \ 347
- Send Alt ] 347
- Send Alt 6 347
- Send Keypad Characters 348
- Send Keypad 349
- Send Keypad / 349
- Send Keypad 0 350
- Send Keypad 2 350
- Send Keypad 1 350
- Send Keypad 5 351
- Send Keypad 4 351
- Send Keypad 3 351
- Send Keypad 6 352
- Send Keypad 8 352
- Send Keypad 7 352
- Send Keypad 9 353
- Send Keypad Enter 353
- Send Keypad Numlock 353
- Send Break Key 354
- Send Delete Key 354
- Send Page Up Key 354
- Send End Key 355
- Send Page Down Key 355
- Send Pause Key 355
- Send Backspace Key 356
- Send Scroll Lock Key 356
- Send Tab Key 356
- Send Insert Key 357
- Send Home Key 357
- Send Print Screen Key 357
- Send Enter Key 358
- Send Up Arrow Key 358
- Send Escape Key 358
- Send Left Arrow Key 359
- Send Down Arrow Key 359
- Send Right Arrow Key 359
- Send Function Key 360
- Send Function Key (Continued) 361
- Send Right Control Key 380
- Send GUI 2 381
- Send GUI 1 381
- Send GUI 0 381
- Send GUI 5 382
- Send GUI 4 382
- Send GUI 3 382
- Send GUI 8 383
- Send GUI 7 383
- Send GUI 6 383
- Send GUI B 384
- Send GUI A 384
- Send GUI 9 384
- Send GUI E 385
- Send GUI D 385
- Send GUI C 385
- Send GUI H 386
- Send GUI G 386
- Send GUI F 386
- Send GUI K 387
- Send GUI J 387
- Send GUI I 387
- Send GUI N 388
- Send GUI M 388
- Send GUI L 388
- Send GUI Q 389
- Send GUI P 389
- Send GUI O 389
- Send GUI T 390
- Send GUI S 390
- Send GUI R 390
- Send GUI W 391
- Send GUI V 391
- Send GUI U 391
- Send GUI Z 392
- Send GUI Y 392
- Send GUI X 392
- Turn On/Off Rule Sets 393
- Turn On Rule Set 4 394
- Turn On Rule Set 3 394
- Turn Off Rule Set 1 394
- Turn Off Rule Set 2 395
- Turn Off Rule Set 4 395
- Turn Off Rule Set 3 395
- Alphanumeric Keyboard 396
- End Of Message 417
- Appendix A 429
- Standard Default Parameters 429
- Appendix B 437
- Programming Reference 437
- M Code 39 Trioptic 438
- N Coupon Code 438
- Code Character Code Type 438
- AIM Code Identifiers 439
- Appendix C 445
- Sample Bar Codes 445
- UPC/EAN (Continued) 446
- Interleaved 2 of 5 446
- 7612341562341 447
- Appendix D 449
- Glossary-2 456
- Glossary-3 457
- Glossary-4 458
- Glossary-5 459
- Glossary-6 460
- Revision A 466
Relacionado con productos y manuales para Escáneres Wasp-bar-code WPS100
Escáneres Wasp-bar-code WLS 9500 Manual de usuario
(189 paginas)
(189 paginas)
Escáneres Wasp-bar-code WWS800 Manual de usuario
(22 paginas)
(22 paginas)
Escáneres Wasp-bar-code WWS850 Manual de usuario
(30 paginas)
(30 paginas)
Escáneres Wasp-bar-code WDT3200 Manual de usuario
(28 paginas)
(28 paginas)
Escáneres Wasp-bar-code WWR2900 Manual de usuario
(44 paginas)
(44 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.249 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales