Wasp-bar-code WLP 4170 CCD Manual de usuario Pagina 1

Wasp WLP 4170 CCDProgramming GuidePlease ReadNote:The Wasp WLP 4170 CCDScanner is ready to scan themost popular bar codes out of the box. This manuals

7Setup & Configuration—Beep and DelayBeep Volume Settings00 None01 Lowest02 Low03 Medium (Default)04 Medium-High05 High06 High-Medium07 HighestThe

8Setup & Configuration—Intercharacter DelayIntercharacter Delay Settings00 Slowest01 Slow02 Default50 Medium75 Fast99 FastestThe 'Intercharac

9Setup & Configuration—Keyboard Wedge00 Keyboard Present*01 Laptop/No keyboardThe 'Keyboard Wedge' configuration supports options relate

*Default00 Default* 04 Continuous10Setup & Configuration—Scanning ModesBeginSet Scanning ModeExitThe 'Scanning Mode' option controls the

Preamble Data Postamble11Setup & Configuration—Preamble and Postamble*DefaultThe 'Preamble' and 'Postamble' options are used t

12Setup & Configuration—Code 39Code 39 is va ri a ble length and is the most frequently used symbology in industri a lbar code systems today and i

13Setup & Configuration—Code 39 (cont.)Standard Code 39 contains only 43 characters (0-9, A-Z, $, /, %, +, -, ., SPAC E )and can be extended to a

14(continued on next page) *DefaultSetup & Configuration—Code128On/OffVerify Check DigitBeginTransmit Check DigitExitOption Alpha/Numeric Entry(Ba

15Setup & Configuration—Code128 (cont.)Set Maximum LengthSet Minimum LengthBeginFormatExitOption Alpha/Numeric Entry(Back Flap)64 - Minimum 00 -

16Setup & Configuration—UPC-AOn/OffVerify Check DigitBeginTransmit Check DigitExitOption Alpha/Numeric Entry(Back Flap)Disable 00Enable 01*Disable

© Copyright Wasp Technologies 2002.All rights reserved.Version 1.0No part of this publication may be reproduced or transmitted in any formor by any me

17Setup & Configuration—UPC-A (cont.)BeginSupplement DigitsTruncate Leading ZeroExitNOTE: For help in configuring these settings, consult the prog

18(continued on next page) *DefaultSetup & Configuration—UPC-EOn/OffVerify Check DigitBeginTransmit Check DigitExitOption Alpha/Numeric Entry(Back

19*DefaultSetup & Configuration—UPC-E (cont.)Supplement DigitsTruncate Leading ZeroBeginExpansionExitNOTE: For help in configuring these settings,

20(continued on next page) *DefaultSetup & Configuration—EAN-13On/OffVerify Check DigitBeginTransmit Check DigitExitOption Alpha/Numeric Entry(Bac

21Setup & Configuration—EAN-13 (cont.)NOTE: For help in configuring these settings, consult the programmingsteps on page 5.The EAN/JAN-13 (Europea

22(continued on next page) *DefaultSetup & Configuration—EAN-8On/OffVerify Check DigitBeginTransmit Check DigitExitOption Alpha/Numeric Entry(Back

23*DefaultSetup & Configuration—EAN-8 (cont.)Supplement DigitsTruncate Leading ZeroBeginExpansionExitOption Alpha/Numeric Entry(Back Flap)None 00*

24Setup & Configuration—Code 93On/OffVerify Check DigitBeginTransmit Check DigitSet Maximum LengthSet Minimum LengthExitOption Alpha/Numeric Entry

25Setup & Configuration—Interleaved 2 of 5*DefaultBeginOn/OffVerify Check DigitTransmit Check DigitExitOption Alpha/Numeric Entry(Back Flap)Disabl

26Setup & Configuration—Codabar*DefaultOn/OffVerify Check DigitBeginTransmit Check DigitSet Maximum LengthExitOption Alpha/Numeric Entry(Back Flap

Table of ContentsChapter 1. Introduction...1Chapter 2. Installation...

27*DefaultSetup & Configuration—Codabar (cont.)Set Minimum LengthStart/Stop TypeBeginStart/Stop TransmissionExitOption Alpha/Numeric Entry(Back Fl

28Setup & Configuration—MSI PlesseyOn/OffVerify Check DigitBeginTransmit Check DigitSet Maximum LengthSet Minimum LengthExitOption Alpha/Numeric E

29Setup & Configuration—PDF417On/OffBeginExitOption Alpha/Numeric Entry(Back Flap)Disable 00*Enable 01NOTE: For help in configuring these settings

30Code 39*Interleaved 2 of 5Codabar*Code 128*MSI/PlesseyCode 93*Setup & Configuration—Bar Code Test Symbols—Appendix ANote: Make sure that the app

31UPC-A*UPC-E*UPC-Ew/5 digit supplementUPC-Ew/2 digit supplementUPC-Aw/2 digit supplementUPC-Aw/5 digit supplementSetup & Configuration—Bar Code T

EAN/JAN 13*EAN/JAN 13w/2 digit supplementEAN/JAN 13w/5 digit supplement3Setup & Configuration—Bar Code Test Symbols—Appendix A (cont.)*Default

EAN/JAN 8*EAN/JAN 8+5w/5 digit supplementEAN/JAN 8w/2 digit supplementPDF41733Setup & Configuration—Bar Code Test Symbols—Appendix A (cont.)*Defau

34Setup & Configuration—WLP 4170 CCD SpecificationsMODEL WLP 4170OPTICALScanning Width 3.2 in (120 mil)Depth of Field 0 to 3 in (0 to 200 mil)Scan

35Wasp Bar Code products are warranted against defects in workmanship andmaterials for a period of one year from the date of shipment, provided that t

43 C44 D45 E46 F47 G48 H49 I4A J4B K4C L4D M4E N4F O50 P51 Q52 R53 S54 T55 U56 V57 W58 X59 Y5A Z5B [5C5D ]5E ^5F _60 `61 a62 b23 #24 $25 %26 &27 ‘

1Chapter 1IntroductionBar coding is the most common Automated Data Collection (ADC) technologyproviding timely, error-free information that can be use

0123456789ABCDEFFINISHBACK COVERBAR CODES

21. Turn off your computer.2. Unplug your PC keyboard cable and plug the male end (Din 5) of the WaspWLP 4170 CCD Scanner directly into your PC keyboa

3Your Wasp WLP 4170 CCD Scanner is ready to go. The default settings of theWasp WLP 4170 CCD Scanner have been pre-programmed for the mostcommon bar c

4Bar codes are symbols consisting of a series of bars and spaces which can beapplied to packages, cartons, bottles, and other commercial products. The

5In order to configure Wasp WLP 4170 CCD Scanner, you must familiarizeyourself with the setup procedures on the following pages. The default settingso

NOTE: Scanning these bar codes returns the scanner tothe factory default settings1. Scan “Begin ”2. Scan “Default” to restore scanner to default setti